If that is easier to walk up a hill 보다 to drive up, girlfriend may have actually a negative fuel filter. Check out on to learn exactly how to replace the fuel filter on her Honda Accord.


This article applies to the Honda Accord (1990-2002).

You are watching: 2000 honda accord fuel filter location

For Honda owners that don"t perform continual maintenance, one of the item that ultimately needs come be replaced is the fuel filter. However it"s not as poor as that sounds. If you space overdue because that this task, girlfriend may notice that under tougher and steeper road problems your Accord could feel sluggish. A experienced can perform this job pretty quickly, but at a price. It may take girlfriend a little bit longer, yet you have the right to do it because that a fraction of the cost. Choose either option, however remember that running through a negative fuel filter will eventually lead come clogged fuel injectors in ~ best. At worst, that may lead to a destroyed fuel pump and also fuel system.

*

Materials NeededNew fuel filter10, 14, and also 17 mm flare nut wrenchesFluid capture panShop rags
Warning

Perform this project in a well-ventilated area because the gas fumes may be harmful.


Step 1 – Disconnect battery and relieve the fuel system pressure

Disconnect the an adverse (black) terminal from the battery. Then, eliminate the gas cap to relieve gas press from the fuel system.

*
Figure 1. Disconnect negative battery terminal before starting.
*
Figure 2. Remove gas cap to relax fuel system pressure.
Pro TipsTo relieve the fuel mechanism pressure, friend can additionally loosen the gas press bolt in ~ the finish of the fuel rail. If you usage the bolt method, make certain that you re-tighten it when the job is finished.If friend don"t relieve the pressure prior to starting, it will be more daunting to remove or unplug all the necessary parts.

Step 2 – situate the fuel filter

The fuel filter ar is different on details model years.

1990-1994: Accord fuel filters are situated on the passenger"s next firewall.1995-2002: Accord fuel filters are situated on the rear of the engine, near the brake grasp cylinder.

Step 3 – remove the reduced fuel line and also the upper fuel heat Banjo bolt

Once you have located the fuel filter, use the 14 mm wrench and rotate counterclockwise to loosen the nut from the lower fuel line. Place the fluid capture pan under this area come catch any kind of spilled gas. Once the seed is removed, traction the reduced fuel line turn off and set it aside. Then, usage the 17 mm flare nut wrench to ease the Banjo bolt on top fuel line. Rotate the wrench counterclockwise to ease the bolt, and also then eliminate the fuel heat by hand.

Figure 3. Eliminate 14 mm bolt native the bottom fuel line.
*
Figure 4. Eliminate 17 mm Banjo bolt from upper fuel line.

Step 4 – eliminate the clamp bolts

Using the 10 mm flare seed wrench, unfasten 2 bolts native the clamp that hold the fuel filter in place.

Figure 5. Eliminate two 10 mm bolts from fuel filter clamp.

Step 5 – replace the fuel filter and reattach the clamp

Unclip the alignment hole holding the optimal of the fuel filter in place, and then remove the fuel filter native the clamp. Dispose that the old filter and also place the brand-new fuel filter in the clamp. Then, insert the fuel filter clamp come its initial location and secure it with the two 10 mm bolts.

Figure 6. Remove and also replace the fuel filter from the clamp.

Step 6 – Reconnect the upper and lower fuel lines

Before reconnecting the upper fuel line, insert two brand-new washers. Then, tighten the 17 mm Banjo bolt to a snug fit. Reconnect the reduced fuel line, and secure it through the the 14 mm bolt to a snug fit together well.

Figure 7. Re-attach the bottom fuel line.
Pro Tip

Your instead of filter may have actually come through replacement washers. If not, you need to replace the washers of the top fuel line once you replace the filter.


Step 7 – Re-check the fuel lines and bolts

Double examine that your fuel lines and also bolts are correctly secure.

Here space the bolts and also corresponding fuel lines:

One 14 mm bolt for the bottom fuel lineOne 17 mm Banjo bolt for the upper fuel lineTwo 10 mm bolts for the fuel filter bracket

Step 8 – check the brand-new fuel filter

Tighten the gas cap (or gas pressure bolt in ~ the finish of the fuel rail), and reconnect the an adverse (black) battery terminal. Rotate the ignition come the "ON" position four times (without starting the engine). This is to prime the new fuel filter with gas. Rotate the engine on because that the 5th turn. Through the vehicle running, examine the brand-new fuel filter for any type of leaks. If girlfriend see any kind of leaks, turn off the engine and re-tighten the fuel lines.

See more: Bra In Hard Sci-Fi, How Is The Bombing Of Hiroshima And Nagasaki Viewed?

*
Figure 8. Twin check the all fittings are secure.

Featured Video: Honda Accord Fuel Filter Replacement


Related Discussions and Site