I had my wait filter adjusted at Wal-Mart and while he had the filter the end he take it the air hose and also blew the dust and dirt off, and also right right into the north hole. It would hardly run and has acquired better, I put cleaner in the gas and also that has actually helped, but I'm thinking now I may have to adjust the fuel filter, can you call me whereby it's located?


You are watching: 2006 nissan altima fuel filter location

*

Hello, Yes the fuel filter is located in the fuel tank attached come the fuel pump, this filter is usually not serviceable. More recent cars carry out no have actually fuel filters favor older cars do. Just a fuel strainer in the tank.This guide should aid with diagrams listed below to show you on your car.https://www.ptcouncil.net/articles/how-to-change-a-fuel-filterCheck out the diagrams (Below). Please let us understand if you require anything rather to get the difficulty fixed.
*

*

auto keeps stalling, jerks, and spits and also sputters; particularly after I put gas in the automobile it will do it a lot.
*



See more: 1 Lb Green Beans Serves How Many Cups Are In One Pound Of Green

The fuel filter is located in the fuel tank. That is considered a lifetime part that never needs service. To accessibility it, the fuel pump assembly needs removed native the tank. Here are the directions for replacement. All attached photos correlate through the directions. Examine out the diagrams (Below). Removal and Installation For every Models other than PZEVNOTE: The Fuel Filter because that this auto is a "Maintenance free Item", and also does no require program service. 1. Unscrew the fuel filler cap to relax the push inside the fuel tank. 2. Relax the fuel pressure from the fuel lines. Refer to "FUEL push RELEASE". 3. Disconnect the battery an adverse terminal. 4. Eliminate the behind seat bottom. 5. Turn the four retainers 90 degrees in a clockwise direction and also remove the fuel pump inspection feet cover.6. Disconnect the fuel level sensor, fuel filter, and fuel pump assembly electrical connector, EVAP hose rapid connector, and the fuel feed hose quick connector from the fuel level sensor unit, fuel filter, and also fuel pump assembly. Remove the fast connector as follows: - hold the sides of the connector, push in tabs and pull the end the tube. - If the connector and also the tube space stuck together, push and pull number of times till they start to move. Climate disconnect castle by pulling. CAUTION: - The tube deserve to be removed as soon as the tabs are totally depressed. Perform not twisted it an ext than necessary. - carry out not use any tools to eliminate the fast connector. - store the resin pipe away native heat. It is in especially careful when welding near the tube. - protect against acid fluid such together battery electrolyte, etc. From getting on the resin tube. - carry out not bending or twisted the tube throughout installation and also removal. - Only as soon as the pipe is replaced, eliminate the continuing to be retainer on the pipe or fuel level sensor, fuel filter, and fuel pump assembly. - as soon as the tube or fuel level sensor, fuel filter, and also fuel pump assembly is replaced, additionally replace the retainer with a new one (green colored retainer). - To store the connecting section clean and also to prevent damage and also foreign materials, cover them completely with plastic bags or something similar.7. Eliminate the lock ring making use of a socket journey handle and also Tool together shown. Tool number : KV991J0090 (J-46214) CAUTION: - Discard the lock ring, do not reuse the lock ring. - Discard the ring seal, execute not reuse the ring seal. 8. Eliminate the fuel level sensor, fuel filter, and fuel pump assembly. CAUTION: - do not bending the rise arm throughout removal. - Discard the ring seal, execute not reuse the ring seal.INSPECTION after REMOVALInspect the fuel level sensor, fuel filter, and fuel pump for any defects and foreign materials. Change as necessary.INSTALLATIONInstallation is in the turning back order the removal. Download the fuel level sensor, fuel filter, and fuel pump assembly with the fuel feed hose encountering the prior of the automobile as shown. Use a new ring seal. - affix the quick connector together follows: - check the connection for damages or any type of foreign materials. - Align the connector v the tube, then insert the connector straight right into the tube until a click is heard.After the pipe is connected, make certain the connection is for sure by performing the following checks: - pull the tube and also the connector to make certain they room securely connected. Visually check that the 2 retainer tabs are associated to the quick connector.Check the end the diagrams (Below). You re welcome let us understand if you need anything rather to gain the problem fixed.