Has one of your power door lock actuators given up on life, leaving you can not to lock or unlock your doors? This short article will go you v the process of replacing her actuators to get those locks functioning properly as soon as again.

You are watching: Ford f150 door lock actuator replacement


This article uses to the Ford F-150.

Power door lock actuators are vital component in your strength lock system, and also though they space a nice simple machine in operation, failure have the right to lead come a non-working system. Actuators function a tiny electric motor that transforms a collection of gears which revolve the actuator rod, which subsequently locks or unlocks her doors. Whether the motor falls short or the gears break, at some point actuators will have to be replaced. Save reading and we"ll to walk you v the process.

*

Materials Needed5 and also 10mm sockets and ratchet through extensionSmall flat head screwdriverPutty knifeRagT27 Torx driver

Step 1 – remove the door panel

Remove the 2 bolts top top the bottom the the door panel, then pry turn off the trim item in the front center section (over the door speaker). Remove the bolts hold the speaker in place, pull it out, and disconnect the harness on the back. Pry off the door move assembly and also disconnect the harness on the back. Eliminate the bolt behind wherein you traction the door move assembly the end from. Pry off the trim piece neighboring the door handle and remove the bolts behind it. Traction the handle out and also lift up on the door dashboard to release it, then disconnect the harness from the back and remove the door panel.

*
Figure 1. Remove the two bolts indigenous the bottom that the door panel.
*
Figure 2. Remove the speak cover.
*
Figure 3. Remove the speaker.
*
Figure 4. Remove the door switch assembly.
*
Figure 5. Eliminate the bolt behind the assembly.
*
Figure 6. Remove the door handle, and also then whole panel.

Step 2 – eliminate the power door lock actuator

Carefully peel back the plastic rain shield attached to the door to prevent ripping it.Pull turn off the two plugs ~ above the external of the door to disclose two 10mm screws, then eliminate the screws.
*
Figure 7. Remove the bolts indigenous the next of the door.Remove the 2 10mm nuts within the door hold the door take care of in ar (Figure 8).Pull out the former of the door handle and slide it forward, climate twist it up at the front and pull down to remove.
*
Figure 8. Remove the screws hold the door handle in place.
*
Figure 9. Remove the door handle.Remove the three T27 Torx screws from around the door latch.Remove the home window guide 10mm screw and also pull the overview out.Remove the clip holding the lock rod in place and also lift approximately release it.
*
Figure 10. Eliminate the Torx screws from the door latch.
*
Figure 11. Remove the bolt stop the lock mechanism.
*
Figure 12. Traction the lock rod out.
Push in on the clip near the bottom of the door utilizing a driver to relax it.Pull the whole lock device up and guide it out of the door.Unplug the harness from the mechanism and use a screwdriver to press out the clips holding the actuator to the mechanism, climate pull it off.
*
Figure 13. Release the clip holding the mechanism in place.
*
Figure 14. Pull the mechanism out.
*
Figure 15. Eliminate the actuator native the assembly.

See more: What Does Slt Mean On A Car, What Is Slt On The Yukon Meen

Step 3 – Install brand-new door lock actuator

Point the lock pole up and also push the new actuator in place. Reconnect the harness and feed the assembly ago in the door. Push the bottom clip back in the door. Reinstall the T27 screws close to the latch to host it in place. Clip in the lock rod and reinstall the cable. Re-clip the harness and reinstall the rest of the screws close to the latch, then tighten. Reinstall the door handle and replace the bolts behind it and in the next of the door, then replace the rubber plugs. Reinstall the plastic water shield end the inside of the door and reinstall the speaker and door panel.